路面冷再生機液壓系統的更換與保養是確保其正常運行和延長使用壽命的重要環節。以下是一些關于路面冷再生機液壓系統更換與保養的常識：

　　The replacement and maintenance of the hydraulic system of the road surface cold recycling machine is an important part to ensure its normal operation and extend its service life. Here are some common knowledge about replacing and maintaining the hydraulic system of the road cold recycling machine:

　　一、液壓系統更換步驟

　　1、 Hydraulic system replacement steps

　　更換時機：

　　Replacement timing:

　　設備運轉結束后，在適當的溫度下（50攝氏度以下）更換液壓油為最佳時機。

　　The best time to replace hydraulic oil is at an appropriate temperature (below 50 degrees Celsius) after the equipment is running.

　　場地條件與器具準備：

　　Site conditions and equipment preparation:

　　場地條件：選擇平整清潔的地面（水泥地面最好）。

　　Site conditions: Choose a flat and clean ground (preferably cement ground).

　　器具：準備三相電源、200L的油桶三個、濾油機一臺（用于更換濾芯）、充足的液壓油（建議使用HV46#及以上低溫冷凝抗磨液壓油）、濾芯一套、濾芯扳手1件。

　　Equipment: Prepare a three-phase power supply, three 200L oil drums, one oil filter (for replacing the filter element), sufficient hydraulic oil (recommended to use HV46 # and above low-temperature condensing anti-wear hydraulic oil), one set of filter elements, and one filter wrench.

　　更換步驟：

　　Replacement steps:

　　先將設備的液壓油抽出。

　　First, extract the hydraulic oil from the equipment.

　　拆下全部液壓油濾芯。

　　Remove all hydraulic oil filter elements.

　　將需要更換的鋼管、膠管安裝好。

　　Install the steel pipes and rubber hoses that need to be replaced.

　　將新液壓油通過濾油機注入。

　　Inject new hydraulic oil through the oil filter.

　　觀察新的油位是否達到標準油位，直到達標為止。

　　Observe whether the new oil level reaches the standard oil level until it meets the standard.

　　啟動設備后，小負荷運轉設備，使液壓油均勻充滿各部位液壓件。

　　After starting the equipment, operate it under low load to evenly fill all hydraulic components with hydraulic oil.

　　二、液壓系統保養常識

　　2、 Common knowledge of hydraulic system maintenance

　　液壓油選擇與更換：

　　Hydraulic oil selection and replacement:

　　路面冷再生機在施工過程中負荷較大、液壓系統溫度較高，因此建議使用HV46#及以上低溫冷凝抗磨液壓油。

　　The road surface cold recycling machine has a high load and hydraulic system temperature during construction, so it is recommended to use HV46 # and above low-temperature condensing anti-wear hydraulic oil.

　　根據工程機械設備對液壓系統的要求，初次對液壓系統和濾芯的保養為500小時，初次保養方案是將油品進行過濾，只更換濾芯；從第二次保養開始為1000小時，可根據油脂情況適當延長保養時間。若設備運轉使用不足1000小時，但工作強度一般，可不更換全部液壓油，但需放出樣品檢查顏色是否清亮、手感粘度是否合適，可采用過濾全部液壓油后更換全部濾芯的方式進行保養。

　　According to the requirements of engineering machinery equipment for hydraulic systems, the initial maintenance of the hydraulic system and filter element is 500 hours. The initial maintenance plan is to filter the oil and only replace the filter element; Starting from the second maintenance, it takes 1000 hours, and the maintenance time can be extended appropriately according to the condition of the grease. If the equipment has been running for less than 1000 hours but the working intensity is average, it is not necessary to replace all hydraulic oil. However, it is necessary to release a sample to check whether the color is clear and whether the hand feel and viscosity are appropriate. The maintenance can be carried out by filtering all hydraulic oil and replacing all filter elements.

　　定期啟動與檢查：

　　Regular start-up and inspection:

　　定期啟動機器并開啟機器上的所有液壓功能，讓液壓驅動元件定期工作，以防止相關的密封件因長時間的停放而損壞，以及油缸桿等金屬元件銹蝕等故障。

　　Regularly start the machine and activate all hydraulic functions on it, allowing the hydraulic drive components to work regularly to prevent damage to related seals due to prolonged parking, as well as rusting of metal components such as oil cylinder rods.

　　在使用過程中，應經常檢查液壓油的油位、油質和油溫，確保液壓系統在正常狀態下工作。

　　During use, the oil level, quality, and temperature of the hydraulic oil should be checked regularly to ensure that the hydraulic system is working properly.

　　清潔與防護：

　　Cleaning and protection:

　　保持液壓系統清潔，防止污染物進入油箱和液壓管路。

　　Keep the hydraulic system clean to prevent contaminants from entering the oil tank and hydraulic pipelines.

　　盡可能地將所有的油缸桿縮到液壓油缸油腔內，以更好地保護油缸桿的表面。

　　As much as possible, retract all cylinder rods into the hydraulic cylinder oil chamber to better protect the surface of the cylinder rods.

　　專業維修與保養：

　　Professional maintenance and upkeep:

　　液壓系統的維修和保養應由專業人員進行，以確保操作正確、安全。

　　The maintenance and upkeep of hydraulic systems should be carried out by professionals to ensure correct and safe operation.

　　在維修和保養過程中，應嚴格遵守相關操作規程和安全規定。

　　During the repair and maintenance process, relevant operating procedures and safety regulations should be strictly followed.

　　綜上所述，路面冷再生機液壓系統的更換與保養需要遵循一定的步驟和常識，以確保其正常運行和延長使用壽命。在更換液壓油時，應注意選擇合適的液壓油、掌握更換時機和步驟；在保養過程中，應定期檢查液壓油、保持系統清潔、定期啟動機器并檢查液壓功能等。同時，液壓系統的維修和保養應由專業人員進行，以確保操作正確、安全。

　　In summary, the replacement and maintenance of the hydraulic system of the road cold recycling machine need to follow certain steps and common sense to ensure its normal operation and extend its service life. When replacing hydraulic oil, attention should be paid to selecting the appropriate hydraulic oil, mastering the timing and steps of replacement; During the maintenance process, it is necessary to regularly check the hydraulic oil, keep the system clean, start the machine regularly, and check the hydraulic function. Meanwhile, the maintenance and upkeep of the hydraulic system should be carried out by professionals to ensure correct and safe operation.

　　本文由 冷再生機租賃 友情奉獻.更多有關的知識請點擊  http://www.tclqgc.com   真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Cold Recycling Machine Rental For more related knowledge, please click http://www.tclqgc.com Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.